Skip to main content
ALUMINIUM Primer
Updated over a week ago
MO-TECH_PRIMER_ALUMINIUM_400ML.jpg

GENERAL INFORMATION

Primer Spray used for pre-treatment of Aluminium surfaces to create a neutral surface which offers the greatest adhesion and protection to apply further paint coatings onto. Provides the longest possible lifespan and most aesthetic finish for further coatings of top paint layers and compensates for extension of Aluminum under the influence of heat.

FEATURES

- Primes & improves adhesion on the top coat

- Limited/ conditionally suitable for copper & zinc

- Weatherproof

INSTRUCTIONS FOR USE

Shake can vigorously for 2-3 minutes before use. Apply ALUMINIUM PRIMER in several thin layers, spraying in sweeping motions. Allow each coating to dry for at least 5 minutes. Can be overpainted after 3 hours. Further coats of alternative products might require a drying time of 24 hours or more depending on application style. Always test spray on a non-visible area to check the compatibility of lacquer or paint. For optimal lifespan, store cans with the nozzle on.

APPLICATION INFORMATION

- Surfaces should be dry and clean of oil, dirt or rust

- Sand back with a fine-grid sandpaper (280-400 grain) and carefully remove all residue afterwards

- Shake the can well for at least 3 minutes

- Spray distance should be at least 25cm/10in

- Test spray on a non-visible area

- Apply at least 2-3 layers in a grid pattern. Leave every layer to dry at least 5 min.

PRODUCT INFORMATION

PRODUCT NAME: Montana Cans TECH Aluminium Primer

ITEM#: 518089

EAN-CODE: 4048500518089

HS CODE: 32082090

COUNTRY OF ORIGIN: Germany

TECHNICAL INFORMATION

CONTENT: 400ml

NOZZLE: Flat Jet - Medium

RECOMMENDED NOZZLES: Flat Jet Medium and Wide

LAQUER BASE: NC-Acrylic

PRESSURE LEVEL: Medium pressure

COLOR: Light grey

GLOSS LEVEL (60° angle according to DIN 67530): 5-10 GE matte

HEAT RESISTANCE: Up to 80°C (176°F)

COVERAGE: Good

OVERPAINTING: Can be overpainted with Synthetic-, Nitro-Combi (NC) or Acrylic Lacquer after approx. three hours drying time

DRYING TIME AT 20°C (68°F) AND 50% RELATIVE HUMIDITY:

- Dust/Touch dry: approx. 15/30 min.

- Overpainting after 3h.

- Fully cured after 24h

Drying time depends on temperature, humidity and thickness of coating.

OPTIMAL PROCESSING CONDITIONS:

- Temperature 10° - 25°Celcius

- Surface temperature 5° - 40°Celcius

- Air humidity max. 60%

SHELF LIFE / STORAGE: 10 years with proper storage (10°-25°C, relative humidity of max. 60%).

DANGEROUS GOODS INFORMATION

- Dangerous goods class 2.1

- UN1950

FREQUENTLY ASKED QUESTIONS

When should I use a primer?

The goal of priming is to create a neutral surface to provide the longest possible lifespan and the most aesthetic finish for further coatings. Montana-Cans Primers are for pre-treatment and preparation of surfaces and will offer the greatest adhesion and protection to apply further coatings onto.

How will using Montana ALUMINIUM PRIMER assist me?

Using Montana ALUMINIUM PRIMER will create the best possible surface for adhesion of further coatings on aluminum to help resist and prevent the onset flaking and cracking. Using the ALUMINIUM PRIMER will also enhance scratch resistance of further applied layers.

When do I use Montana ALUMINIUM PRIMER?

Montana ALUMINIUM PRIMER is specifically created for the pre-treatment of aluminium and in some cases copper and zinc. Surfaces need to be clean, dry and free of all dust and oils before application. We suggest testing on a non-visible area of your material to check for compatibility.

How do I start using my Montana ALUMINIUM PRIMER?

Remove the nozzle and turn the can upside down. Strike with your palm to allow the safety ring to fall out. Shake vigorously for 2-3 minutes with mixing balls moving freely. Place nozzle back on the valve and test spray.

Which coatings can apply over the ALUMINIUM PRIMER?

You can apply any Montana-Cans color, tech or effect spray on primed surfaces after fully curing.

How long does Montana-Cans ALUMINIUM PRIMER take to dry?

Complete drying time is usually 2-4 hours, however re-coating is possible after approx. 5 minutes.

Can I use other paints, materials & application forms on primed surfaces?

It is possible to combine other materials & Montana-Cans ALUMINIUM PRIMER – However, we suggest to always test for compatibility on a non-visible area.

Pls Note:

This technical application information is given to the best of our knowledge. However, it is only intended as non-binding information and does not release you from the obligation to carry out your own tests on the products supplied by us to determine their suitability for the intended applications. Application and processing are beyond our control and are therefore in the responsibility of the user. Montana Cans shall be released from liability

unless the liability-based incident is caused by a fault incurred to Montana Cans.

Did this answer your question?